一、產品簡介：

     符合我國標線技術標準GB/T16311-2005的要求。

　　the product introduction:

　　The pavement marking thickness measuring instrument is designed and produced by Shanghai Rongjiida Experimental Instrument Co.,Ltd.for measuring the thickness of marking lines for production,quality supervision,engineering construction and supervision.Designed and produced for measuring the thickness of marking lines for production,quality supervision,engineering construction and supervision.It meets the requirements of China's marking technical standard GB/T16311-2005.

　　二、技術參數：

　　★測量范圍：0~12毫米

　　★測量精度：0.01毫米

　　★外形尺寸：140X110X30mm

　　★重量：0.9kg

　　★結構合理

　　★操作簡單

　　★具備數字保持功能

　　★測量精度高

　　★測量安全

　　★可靠性好

　　Second,technical parameters:

　　★Measurement range:0~12 mm

　　★Measurement accuracy:0.01 mm

　　★Dimensions:140X110X30mm

　　★Weight:0.9kg

　　★Reasonable structure

　　★easy to operate

　　★with digital hold function

　　★High measurement accuracy

　　★Measurement safety

　　★Good reliability

　　三、操作步驟：

　　★準備：將測量底座和移動平塊(測厚度機構)處于同一水平上，再將數字式高精度百分表頭置入測厚度機構的安裝座內,然后調緊螺釘。

　　★顯示屏讀書清零：將數字式高精度百分表頭顯示屏清零。

　　★測量：將測量底座置于待測標線上面，使其與移動塊的接合處的邊緣與標線邊緣平行，移動塊能夠自由落下或下移即可測量標線的厚度。為便于讀數可按數字式高精度百分表頭的保持按鈕，提起標線厚度測定儀讀取并記錄數值。

　　Third,the operation steps:

　　★Preparation:Place the measuring base and the moving flat block(measuring thickness mechanism)at the same level,then place the digital high-precision dial indicator head into the mounting of the thickness measuring mechanism,ａnd then tighten the screws.

　　★Display reading clear:Clear the digital high-precision dial indicator display.

　　★Measurement:Place the measuring base on the marking line to be measured so that the edge of the joint with the moving block is parallel to the edge of the marking.The moving block can freely fall or move down to measure the thickness of the marking.To facilitate reading,press the hold button of the digital high-precision dial indicator and lift the line thickness gauge to read and record the value.

　　四、注意事項：

　　★為了保障測量結果的準確度，在測量前應盡量調整好標線厚度測量儀的零值。

　　★為了確保移動塊的移動應在試驗前應注意調整好其與標線的相對位置。

　　同時應清潔標線測量區域的表面，可獲得較真實的測量數據。

　　★測量時應注意解除數字式高精度百（千）分表頭的保持功能，一般連續按保持按鈕3次即可，讓標線厚度測定儀處于測量狀態。

　　★注意防止儀器在測量過程的跌落，以免儀器的損壞。長時間沒有測量任務時應取出數字式高精度百（千）分表的電池，以延長其使用壽命。

　　★測定器及其附件應存放在干燥、清潔、無振動、無易燃、易腐蝕物品的環境條件下。

　　Fourth,note:

　　★In order to ensure the accuracy of the measurement results,the zero value of the line thickness gauge should be adjusted as much as possible before measurement.

　　★In order to ensure the movement of the moving block,it should be adjusted before the test to adjust its relative position with the marking.

　　At the same time,the surface of the measuring area of the marking should be cleaned to obtain more realistic measurement data.

　　★When measuring,please pay attention to the digital high-precision hundred(thousand)sub-head retention function.Generally,press the hold button 3 times continuously,ａnd let the marking thickness gauge be in the measurement state.

　　★Take care to prevent the instrument from falling during the measurement process to avoid damage to the instrument.When there is no measurement task for a long time,the digital high-precision 100(minute)meter battery should be taken out to prolong its service life.

　　★The measuring device and its accessories should be stored in an environment that is dry,clean,vibration-free,flammable and corrosive.