西門子6ES75121CK000AB0型號及參數 西門子6ES75121CK000AB0型號及參數 

6ES7512-1DK01-0AB0 SIMATIC DP,CPU 1512SP-1 PN 用于 ET 200SP, *處理器 mit 工作存儲器 200 KB 用于 程序 和 1MByte 用于數據, 1. 接口:PROFINET IRT mit 3 Port 換機, 48 NS Bit-Performance, SIMATIC Memory 卡 必要, 總線適配器 必要 用于 Port 1 和 2

公司名稱：上海朔川電氣設備有限公司

• 聯 系 人：吉夢琪
• ：
• 地址：上海市金山區涇波路129號
• ：2840735331

• CPU 1512SP-1 PN 訂貨數據   附件   產品信息   組態工具 跳轉到 概述 應用 設計 功能 技術規范 概述 CPU 1512SP-1 PN 適用于基于 S7-1500 CPU 1513-1 PN 的 SIMATIC ET 200SP 適用于對程序范圍和處理速度具有中等要求的應用，通過 PROFINET IO 和 PROFIBUS DP 進行分布式配置。 增強了系統和設備的可用性 可連接zui多 128 個 IO 設備的 PROFINET IO 控制器 PROFINET I-Device，用于連接作為智能 PROFINET 設備、帶 SIMATIC 或第三方 PROFINET I/O 控制器的 CPU 適用于 4 個控制器的 PROFINET 共享智能設備 PROFINET IO IRT 接口，帶集成 3 端換機 經由 PROFINET 的等時同步模式 具有多種通信功能： 編程器/OP 通信，PROFINET IO，開放式 IE 通信（TCP，ISO-on-TCP 和 UDP），Web 服務器和 S7 通信 （帶可裝載的 FB） OPC UA Server (Data Access) 作為運行系統選件，用于方便地將 SIMATIC ET 200SP 連接到第三方設備/系統 可選 PROFIBUS DP 主站，用于 125 個 PROFIBUS DP 從站（帶 CM DP 模塊 6ES7545-5DA00-0AB0） 可選 PROFIBUS DP 從站（帶 CM DP 模塊 6ES7545-5DA00-0AB0） 組態控制（選項處理） 集成運動控制功能，用于控制速度控制軸和定位軸，支持外部編碼器，凸輪/凸輪軌道和探頭 注 CPU 的運行需要使用 SIMATIC 存儲卡。 總線適配器不在供貨范圍內，需要單獨訂購。 應用 CPU 1512SP-1 PN 適用于獨立生產技術領域中對處理性能和響應速度具有中等要求的應用。CPU 1512SP-1 PN 可被用作 PROFINET IO 控制器或分布智能系統（PROFINET 智能設備）。集成式 PROFINET IO IRT 接口的設計形式為 3 端換機，這樣就可以在系統中通過端口 1 和 2 建立總線型拓撲，并且也可通過端口 3 來連接編程設備/PC 或 HMI 設備。 作為智能設備使用時，CPU 1512SP-1 PN 可實現在本地對過程數據進行分布式預處理，并且僅將實際需要的信息傳輸?shù)缴衔豢刂破鳌＿@樣做有以下優勢： 減輕*控制器的工作負荷 縮短對現場重要信號的響應時間 數據量減少，總線系統上的負荷降低 各單元經過預測試并進行平行調試，設置更快速 由于自帶機械裝置,增加了可用性和靈活性 組態清晰明了 CPU 1512SP-1 PN *獨立于*控制器運行。如果其發生故障，CPU 1512SP-1 PN 仍繼續運行。 位模塊化設計的 ET 200SP I/O 系統和 CPU 1512SP-1 PN 可實現面向功能的站設計。 另外，CPU 通過易組態的塊提供全面控制功能，以及通過標準化 PLC-open 塊 提供連接至驅動器的能力。 設計 CPU 1512SP-1 PN CPU 可直接卡裝到標準安裝導軌上。它具有： A powerful processor: The CPU achieves command execution times as low as 48 ns per binary instruction. 大容量工作存儲器： 200 KB 用于程序，1 MB 用于數據 SIMATIC 存儲卡作為裝載存儲器； 允許附加固件更新、數據日志和歸檔等功能 位模塊化擴展性，靈活性好； 任意組合達 64 個 I/O 模塊（I/O 模塊、工藝模塊和通信模塊）。zui大 1 m 的站寬度。 采用 ET 200AL 的混合配置；  通過“BU-Send”基本單元和“BA-Send”總線適配器，可以在可擴展的 I/O 系統 ET 200SP (IP20) 裝置中集成進 ET 200AL (IP65/IP67) I/O 系統的zui多 16 個 I/O 模塊。 PROFINET IO IRT 接口，帶集成 3 端換機： 端口 1 和 2 通過總線適配器來連接 （CPU 1512SP-1 PN 未提供總線適配器，不使用該適配器也可運行）。 如果需要，可以單獨訂購適當?shù)目偩€適配器（BA 2xRJ45、BA 2xFC、BA 2xSCRJ、BA SCRJ/RJ45、BA SCRJ/FC、BA 2xLC、BA LC/RJ45 或 BA LC/FC）。 端口 3 集成式 RJ45 接口 集成通信功能： 編程器/OP 通信 PROFINET IO 開放式 IE 通訊（TCP，ISO-on-TCP 和 UDP） OPC UA 服務器 (數據存取) Web 服務器 S7 通信 S7 路由 數據集路由 免維護數據備份（無電池） 用于錯誤 (Error)、運行狀況 (RUN/Stop)、維護 (MT)、電源 (PWR) 以及每個端口一個鏈路 LED 的診斷顯示 可選標簽采用淺灰色或黃色標簽條。有兩種材料可供選擇： 標簽箔和帶有 500 個標簽條的標簽卷，用于熱轉印打印機 標簽紙 (280 g/m2)，規格 DIN A4，每張 100 個標簽條，適用于激光打印機 ET 200SP CPU 可帶有一個參考 ID 標簽 借助于總線適配器，可實現不同的 PROFINET 連接類型 在具有中等機械及 EMC 負荷的標準應用中，可以使用帶 RJ45 接口的 SIMATIC 總線適配器，如總線適配器 BA 2xRJ45。 對于設備上承受較高機械和/或 EMC 負荷的機械設備和系統，建議使用可連接 FastConnect (FC) 電纜或光纜（SCRJ 或 LC）的 SIMATIC 總線適配器。同樣，帶有光纖電纜接口（SCRJ、LC）的所有 SIMATIC 總線適配器可用于更高的負載。 帶有光纖電纜連接用總線適配器可用于覆蓋兩個站和/或較高 EMC 負載之間的較高電位差。 在將 AC I/O 模塊或 AI Energy Meter ST 用作*個 I/O 模塊時，應將深色的基本單元用作 ET 200SP CPU 后面的*個基本單元 供貨清單： CPU 1512SP-1 PN（包括服務器模塊）、24 V DC 連接器和總線適配器端口蓋（總線適配器須單獨訂購） 功能 高效性 高速命令處理 功能強大的網絡接口： 每個 CPU 均配備 PROFINET IO IRT (3 端機) 作為標準接口。 集成技術 通過標準化的塊 (PLCopen) 連接模擬驅動器和具有 PROFIdrive 功能的驅動器 支持轉速控制軸和定位軸以及外部編碼器 精確位置傳動可實現軸之間的同步操作 具有所有 CPU 變量的跟蹤功能，用于實時診斷和偶發故障檢測 全面的控制功能，例如，通過便于組態的塊可自動優化控制參數實現*控制質量 等時同步模式 通過恒定總線循環時間，將分布式信號采集、信號傳輸和程序執行與 PROFIBUS 循環進行同步 集成安全功能 通過密碼進行知識保護，防止未經許可證讀取和修改程序塊 通過復制保護，可綁定 SIMATIC 存儲卡的程序塊和序列號：只有在將配置的存儲卡插到 CPU 中時，該程序塊才可運行。 4-級 *理念：與 HMI 設備的通信也會受到限制。 操作保護：控制器識別已改變的或未經*的工程組態數據的傳輸 集成式系統診斷 TIA Portal 中、HMI 設備上以及 Web 服務器上以普通文本形式*顯示系統診斷信息（甚至能顯示來自變頻器的消息），即使 CPU 處于停止模式也會進行更新。 集成在 CPU 的固件中，無須進行特殊組態。 通過集中設置進行組態控制（選項處理） 控制器中可存儲各種硬件配置： 在用戶程序中修改配置（啟動 OB100） 配置結束時改裝選件 可使用占位模塊。 SIMATIC 存儲卡(用來運行 CPU) 用作插入式裝載存儲器，或用于更新固件。 還可用于存儲附加文檔或 csv 文件（用于配方和歸檔） 通過用戶程序的系統函數創建數據塊實現數據存儲/讀取 數據記錄（歸檔）和配方 配方和歸檔以 csv 文件保存在 SIMATIC 存儲卡中； 便于使用 Office 工具或通過 web 服務器，訪問工廠運行數據 通過 Web 瀏覽器或 SD 讀卡器，可方便地訪問機器的組態數據（與控制器之間的雙向數據換） 編程 使用 STEP 7 Professional V13 update 3 或更高版本進行編程 技術規范 Article number 6ES7512-1DK01-0AB0   CPU 1512SP-1 PN, 200KB PROG./1MB DATA General information   Product type designation CPU 1512SP-1 PN HW functional status FS03 Firmware version V2.1 Product function   ● I&M data Yes; I&M0 to I&M3 Engineering with   ● STEP 7 TIA Portal configurable/integrated as of version V14 SP1 (FW V2.1) / V13 SP1 Update 4 (FW V1.8) or higher Configuration control   via dataset Yes Control elements   Mode selector switch 1 Supply voltage   Type of supply voltage 24 V DC permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Mains buffering   ● Mains/voltage failure stored energy time 5 ms Input current   Current consumption (rated value) 0.6 A Inrush current, max. 4.7 A; Rated value I²t 0.14 A²·s Power   Infeed power to the backplane bus 8.75 W Power loss   Power loss, typ. 5.6 W Memory   Number of slots for SIMATIC memory card 1 SIMATIC memory card required Yes Work memory   ● integrated (for program) 200 kbyte ● integrated (for data) 1 Mbyte Load memory   ● Plug-in (SIMATIC Memory Card), max. 32 Gbyte Backup   ● maintenance-free Yes CPU processing times   for bit operations, typ. 48 ns for word operations, typ. 58 ns for fixed point arithmetic, typ. 77 ns for floating point arithmetic, typ. 307 ns CPU-blocks   Number of elements (total) 2 000; Blocks (OB, FB, FC, DB) and UDTs DB   ● Number range 1 ... 60 999; subdivided into: number range that can be used by the user: 1 ... 59 999, and number range of DBs created via SFC 86: 60 000 ... 60 999 ● Size, max. 1 Mbyte; For DBs with absolute addressing, the max. size is 64 KB FB   ● Number range 0 ... 65 535 ● Size, max. 200 kbyte FC   ● Number range 0 ... 65 535 ● Size, max. 200 kbyte OB   ● Size, max. 200 kbyte ● Number of free cycle OBs 100 ● Number of time alarm OBs 20 ● Number of delay alarm OBs 20 ● Number of cyclic interrupt OBs 20 ● Number of process alarm OBs 50 ● Number of DPV1 alarm OBs 3 ● Number of isochronous mode OBs 1 ● Number of technology synchronous alarm OBs 2 ● Number of startup OBs 100 ● Number of asynchronous error OBs 4 ● Number of synchronous error OBs 2 ● Number of diagnostic alarm OBs 1 Nesting depth   ● per priority class 24 Counters, timers and their retentivity   S7 counter   ● Number 2 048 Retentivity   — adjustable Yes IEC counter   ● Number Any (only limited by the main memory) Retentivity   — adjustable Yes S7 times   ● Number 2 048 Retentivity   — adjustable Yes IEC timer   ● Number Any (only limited by the main memory) Retentivity   — adjustable Yes Data areas and their retentivity   Retentive data area (incl. timers, counters, flags), max. 128 kbyte; Available retentive memory for bit memories, timers, counters, DBs, and technology data (axes): 88 KB Flag   ● Number, max. 16 kbyte ● Number of clock memories 8; 8 clock memory bits, grouped into one clock memory byte Data blocks   ● Retentivity adjustable Yes ● Retentivity preset No Local data   ● per priority class, max. 64 kbyte; max. 16 KB per block Address area   Number of IO modules 2 048; max. number of modules / submodules I/O address area   ● Inputs 32 kbyte; All inputs are in the process image ● Outputs 32 kbyte; All outputs are in the process image per integrated IO subsystem   — Inputs (volume) 8 kbyte — Outputs (volume) 8 kbyte per CM/CP   — Inputs (volume) 8 kbyte — Outputs (volume) 8 kbyte Subprocess images   ● Number of subprocess images, max. 32 Address space per module   ● Address space per module, max. 288 byte; For input and output data respectively Address space per station   ● Address space per station, max. 2 560 byte; for central inputs and outputs; depending on configuration; 2 048 bytes for ET 200SP modules + 512 bytes for ET 200AL modules Hardware configuration   Number of distributed IO systems 32; A distributed I/O system is characterized not only by the integration of distributed I/O via PROFINET or PROFIBUS communication modules, but also by the connection of I/O via AS-i master modules or links (e.g. IE/PB-Link) Number of DP masters   ● Via CM 1 Number of IO Controllers   ● integrated 1 ● Via CM 0 Rack   ● Modules per rack, max. 80; CPU + 64 modules + server module (mounting width max. 1 m) + 16 ET 200AL modules ● Number of lines, max. 1 PtP CM   ● Number of PtP CMs the number of connectable PtP CMs is only limited by the number of available slots Time of day   Clock   ● Type Hardware clock ● Backup time 6 wk; At 40 °C ambient temperature, typically ● Deviation per day, max. 10 s; Typ.: 2 s Operating hours counter   ● Number 16 Clock synchronization   ● supported Yes ● to DP, master Yes; Via CM DP module ● to DP, slave Yes; Via CM DP module ● in AS, master Yes ● in AS, slave Yes ● on Ethernet via NTP Yes Interfaces   Number of PROFINET interfaces 1 Number of PROFIBUS interfaces 1; Via CM DP module With optical interface Yes; via BusAdapter 1. Interface   Interface types   ● Number of ports 3; 1. integr. + 2. via BusAdapter ● integrated switch Yes ● RJ 45 (Ethernet) Yes; X1 P3; opt. X1 P1 and X1 P2 via BusAdapter BA 2x RJ45 ● BusAdapter (PROFINET) Yes; Compatible BusAdapter: BA 2x RJ45, BA 2x FC, BA 2x SCRJ, BA SCRJ / RJ45, BA SCRJ / FC, BA 2x LC, BA LC / RJ45, BA LC / FC Functionality   ● IP protocol Yes; *4 ● PROFINET IO Controller Yes ● PROFINET IO Device Yes ● SIMATIC communication Yes ● Open IE communication Yes ● Web server Yes ● Media redundancy Yes PROFINET IO Controller   Services   — PG/OP communication Yes — S7 routing Yes — Isochronous mode Yes — Open IE communication Yes — IRT Yes — MRP Yes; As MRP redundancy manager and/or MRP client; max. number of devices in the ring: 50 — MRPD Yes; Requirement: IRT — PROFIenergy Yes — Prioritized startup Yes; Max. 32 PROFINET devices — Number of connectable IO Devices, max. 128; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET — Of which IO devices with IRT, max. 64 — Number of connectable IO Devices for RT, max. 128 — of which in line, max. 128 — Number of IO Devices that can be simultaneously activated/deactivated, max. 8; in total across all interfaces — Number of IO Devices per tool, max. 8 — Updating times The minimum value of the update time also depends on communication share set for PROFINET IO, on the number of IO devices, and on the quantity of configured user data Update time for IRT   — for send cycle of 250 µs 250 μs to 4 ms; Note: In the case of IRT with isochronous mode, the minimum update time of 500 µs of the isochronous OB is decisive — for send cycle of 500 µs 500 µs to 8 ms — for send cycle of 1 ms 1 ms to 16 ms — for send cycle of 2 ms 2 ms to 32 ms — for send cycle of 4 ms 4 ms to 64 ms — With IRT and parameterization of "odd" send cycles Update time = set "odd" send clock (any multiple of 125 µs: 375 µs, 625 µs ... 3 875 µs) Update time for RT   — for send cycle of 250 µs 250 µs to 128 ms — for send cycle of 500 µs 500 µs to 256 ms — for send cycle of 1 ms 1 ms to 512 ms — for send cycle of 2 ms 2 ms to 512 ms — for send cycle of 4 ms 4 ms to 512 ms PROFINET IO Device   Services   — PG/OP communication Yes — S7 routing Yes — Isochronous mode No — Open IE communication Yes — IRT Yes — MRP Yes — MRPD Yes; Requirement: IRT — PROFIenergy Yes — Shared device Yes — Number of IO Controllers with shared device, max. 4 2. Interface   Interface types   ● Number of ports 1 ● RS 485 Yes; Via CM DP module Functionality   ● PROFIBUS DP master Yes ● PROFIBUS DP slave Yes ● SIMATIC communication Yes Interface types   RJ 45 (Ethernet)   ● 100 Mbps Yes ● Autonegotiation Yes ● Autocrossing Yes ● Industrial Ethernet status LED Yes RS 485   ● Transmission rate, max. 12 Mbit/s Protocols   Number of connections   ● Number of connections, max. 128; via integrated interfaces of the CPU and connected CPs / CMs ● Number of connections reserved for ES/HMI/web 10 ● Number of connections via integrated interfaces 88 ● Number of connections per CP/CM 32 ● Number of S7 routing paths 16 SIMATIC communication   ● S7 communication, as server Yes ● S7 communication, as client Yes ● User data per job, max. See online help (S7 communication, user data size) Open IE communication   ● TCP/IP Yes — Data length, max. 64 kbyte — several passive connections per port, supported Yes ● ISO-on-TCP (RFC1006) Yes — Data length, max. 64 kbyte ● UDP Yes — Data length, max. 1 472 byte — UDP multicast Yes; Max. 5 multicast circuits ● DHCP No ● SNMP Yes ● DCP Yes ● LLDP Yes Web server   ● HTTP Yes; Standard and user pages ● HTTPS Yes; Standard and user pages PROFIBUS DP master   ● Number of connections, max. 48 Services   — PG/OP communication Yes — S7 routing Yes — Data record routing Yes — Isochronous mode No — Equidistance No — Number of DP slaves 125; In total, up to 512 distributed I/O devices can be connected via AS-i, PROFIBUS or PROFINET — Activation/deactivation of DP slaves Yes OPC UA   ● OPC UA Server Yes; Data access (read, write, subscribe), runtime license required — Application authentication Yes — Security policies Available security policies: None, Basic128Rsa15, Basic256Rsa15, Basic256Sha256 — User authentication "anonymous" or by user name & password Further protocols   ● MODBUS Yes; MODBUS TCP Media redundancy   ● Switchover time on line break, typ. 200 ms; For MRP, bumpless for MRPD ● Number of stations in the ring, max. 50 Isochronous mode   Isochronous operation (application synchronized up to terminal) Yes; Only with PROFINET; with minimum OB 6x cycle of 625 µs S7 message functions   Number of login stations for message functions, max. 32 Program alarms Yes Number of configurable program alarms 5 000 Number of simultaneously active program alarms   ● Number of program alarms 300 ● Number of alarms for system diagnostics 100 ● Number of alarms for motion technology objects 80 Test commissioning functions   Joint commission (Team Engineering) Yes; Parallel online access possible for up to 3 engineering systems Status block Yes; Up to 8 simultaneously (in total across all ES clients) Single step No Status/control   ● Status/control variable Yes ● Variables Inputs/outputs, memory bits, DBs, distributed I/Os, timers, counters ● Number of variables, max.   — of which status variables, max. 200; per job — of which control variables, max. 200; per job Forcing   ● Forcing Yes ● Forcing, variables Peripheral inputs/outputs ● Number of variables, max. 200 Diagnostic buffer   ● present Yes ● Number of entries, max. 1 000 — of which powerfail-proof 500 Traces   ● Number of configurable Traces 4; Up to 512 KB of data per trace are possible Interrupts/diagnostics/status information   Diagnostics indication LED   ● RUN/STOP LED Yes ● ERROR LED Yes ● MAINT LED Yes ● Monitoring of the supply voltage (PWR-LED) Yes ● Connection display LINK TX/RX Yes Supported technology objects   Motion Control Yes; Note: The number of axes affects the cycle time of the PLC program; selection guide via the TIA Selection Tool or SIZER ● Number of available Motion Control resources for technology objects (except cam disks) 800 ● Required Motion Control resources   — per speed-controlled axis 40 — per positioning axis 80 — per synchronous axis 160 — per external encoder 80 — per output cam 20 — per cam track 160 — per probe 40 ● Positioning axis   — Number of positioning axes at motion control cycle of 4 ms (typical value) 5 — Number of positioning axes at motion control cycle of 8 ms (typical value) 10 Controller   ● PID_Compact Yes; Universal PID controller with integrated optimization ● PID_3Step Yes; PID controller with integrated optimization for valves ● PID-Temp Yes; PID controller with integrated optimization for temperature Counting and measuring   ● High-speed counter Yes Ambient conditions   Ambient temperature during operation   ● horizontal installation, min. 0 °C ● horizontal installation, max. 60 °C ● vertical installation, min. 0 °C ● vertical installation, max. 50 °C Ambient temperature during storage/transportation   ● min. -40 °C ● max. 70 °C Configuration   Programming   Programming language   — LAD Yes — FBD Yes — STL Yes — SCL Yes — GRAPH Yes Know-how protection   ● User program protection/password protection Yes ● Copy protection Yes ● Block protection Yes Access protection   ● Protection level: Write protection Yes ● Protection level: Read/write protection Yes ● Protection level: Complete protection Yes Cycle time monitoring   ● lower limit adjustable minimum cycle time ● upper limit adjustable maximum cycle time Dimensions   Width 100 mm Height 117 mm Depth 75 mm Weights   Weight, approx. 310 g

  全部關于 CPU 1512SP-1 PN 產品與解決方案在線目錄與訂購系統技術信息服務與支持與合作伙伴服務項目