原裝*進口,IPEH-004061包郵。 德國PEAK進口PCAN-USB ProFD:高速USB 2.0轉CAN FD和LIN接口
深圳市宏美瑞科技有限公司為您介紹:
全國代理,*全新*,廠家標準保修2年,報價含運費(順豐快遞)!現貨!
PCAN-USB Pro FD適配器可通過USB把CAN FD和LIN網絡連接到電腦。兩種現場總線可同時連接,用相應的電纜 (2 x CAN FD, 2 x LIN)可連接zui多4路。每個CAN FD通道單獨和USB和LIN電氣隔離,達到500 V。使用簡單并且它堅固的鋁合金殼使該接口特別適用于隨身攜帶外出使用。
D-Sub接口引腳圖

管腳 | 管腳定義 |
---|
1 | 沒有連接 / 可選 +5V |
2 | CAN-L |
3 | GND |
4 | 沒有連接 |
5 | 沒有連接 |
6 | GND |
7 | CAN-H |
8 | 沒有連接 |
9 | 沒有連接 |
新的CAN FD標準 (CAN with Flexible Data Rate) 主要特點是更高的數據傳輸帶寬。zui大64數據位每個CAN FD幀 (代替目前的8位) 可以zui大12 Mbit/s比特率傳輸。CAN FD向下兼容CAN 2.0 A/B標準,因此CAN FD節點可用于現有的CAN網絡。但是,在這種情況下,CAN FD擴展不適用。
特性
- 適配器用于高速USB 2.0 (兼容USB 1.1 和 USB 3.0)
- 發送和接收CAN FD 和 LIN 報文使用2個 D-Sub連接器(都有CAN FD 和 LIN 總線分配)
- 時間戳分辨率1 μs
- 在D-Sub連接器上的5-V供電可通過焊接跳線連接,例如外部總線轉換器。
- 通過USB供電
- 擴展的工作溫度范圍從-40 to 85 °C (-40 to 185 °F)
CAN工作特性
- 符合CAN規范 2.0 A/B 和 FD 1.0
- CAN FD比特率用于數據域 (64位zui大) 從40 kbit/szui大至12 Mbit/s
- CAN比特率從40 kbit/szui大至1 Mbit/s
- CAN FD控制器的FPGA實施
- NXP TJA1044GT CAN收發器
- 每個CAN FD通道獨立光解耦USB和LIN,zui大500 V
- CAN端子可通過焊接跳線激活
- 總線負載測量包括錯誤幀和過載幀
- 誘發錯誤發生功能用于進入和外出CAN報文
LIN工作特性
- 比特率從1 kbit/s zui大至20 kbit/s
- TJA1021/20 LIN收發器
- 兩個LIN通道 (共地) 光解耦 USB 和 CAN FD
- 可被用作LIN主站或從站 (1 ms主站任務分辨率)
- 自動比特率、幀長度、和校驗和類識別
- 自發調度器,支持無條件、事件、和零星幀
- 硬件可工作于時間表 (zui大8個時間表可用總共256個間隙位配置)
發貨清單
- PCAN-USB Pro FD接口(鋁合金外殼)
- CAN FD接口驅動 for Windows® 8.1, 7, Vista and Linux (32/64 bit)
- LIN接口驅動 for Windows® 8.1, 7, Vista (32/64 bit)
- PCAN-View CAN監視器Windows軟件
- PLIN-View Pro LIN監視器Windows軟件
- PCAN-Basic 編程接口包括接口DLL、例程、和所有常用編程語言的頭文件
- PLIN-API編程接口包括接口DLL、例程、和所有常用編程語言的頭文件
- PDF格式的說明書
The PCAN-USB Pro FD adapter enables the connection of CAN FD and LIN networks to a computer via USB. Two field busses can be connected at the same time, up to four with appropriate adapter cables (2 x CAN FD, 2 x LIN). Each CAN FD channel is separay isolated against USB and LIN with a maximum of 500 Volts. Its robust aluminum casing makes the PCAN-USB Pro FD adapter suitable for applications.
The new CAN FD standard (CAN with Flexible Data rate) is primarily characterized by higher bandwidth for data transfer. The maximum of 64 data bytes per CAN FD frame (instead of 8 so far) can be transmitted with bit rates up to 12 Mbit/s. CAN FD is downward-compatible to the CAN 2.0 A/B standard, thus CAN FD nodes can be used in existing CAN networks. However, in this case the CAN FD extensions are not applicable.
The monitor software PCAN-View and the programming interface PCAN-Basic for the development of applications with CAN connection are included in the scope of supply and support the new standard CAN FD. The monitor application PLIN-View Pro as well as the PLIN programming interface are also included in the scope of supply.
- Adapter for High-speed USB 2.0 (compatible to USB 1.1 and USB 3.0)
- Transmitting and receiving of CAN FD and LIN messages using 2 D-Sub connections (both with pin assignment for the CAN FD and LIN bus)
- Time stamp resolution 1 μs
- 5-Volt supply at the D-Sub connector can be activated through a solder jumper, e.g. for external bus converter
- Voltage supply via USB
- Extended operating temperature range from
-40 to 85 °C (-40 to 185 °F)
CAN operation properties:
- Complies with CAN specifications 2.0 A/B and FD
- CAN FD support for ISO and Non-ISO standards switchable
- CAN FD bit rates for the data field (64 bytes max.) from 25 kbit/s up to 12 Mbit/s
- CAN bit rates from 25 kbit/s up to 1 Mbit/s
- FPGA implementation of the CAN FD controller
- NXP TJA1044GT CAN transceiver
- Each CAN FD channel is separay opto-decoupled against USB and LIN up to 500 V
- CAN termination can be activated through a solder jumper, separay for each CAN channel
- Measurement of bus load including error frames and overload frames on the physical bus
- Induced error generation for incoming and outgoing CAN messages
LIN operation properties:
- Bit rates from 1 kbit/s up to 20 kbit/s
- TJA1021/20 LIN transceiver
- Both LIN channels (common ground) are optodecoupled against USB and CAN FD
- Can be used as a LIN master or slave (1 ms master task resolution)
- Automatic bit rate, frame length, and checksum type recognition
- Autonomous scheduler with support for unconditional, event, and sporadic frames
- Hardware can work through a schedule table (up to 8 schedule tables can be configured with a total of 256 slots)