FDJ-120風動手持切開鋸是我公司關于高危，安全系數請求特別高的作業環境，如化工.治煉廠.天然氣挖掘.高危潮濕的地道，水下及狹窄的空間作業，尤其是高瓦斯防爆礦井。山西萬澤錦達礦山機械設備有限公司自立研制的新式多用途風動手持切開東西。它使用中國臺灣進口氣動馬達作為動力輸出，使用壓縮空氣作為動力源，不必電源。風動手持切開鋸不光整機分量輕，操作簡略，攜帶方便零火花，進步作業效益。本商品安全可靠是高危職業的抱負氣動切開東西。
FDJ-120風動切割鋸技術參數:
1：適用資料:不銹鋼.鋁，銅.鉻合金，鎳基合金，玻璃，纖維，木材，塑料，鋼絲繩等。
2：切開規模：120mm*120mm圓型資料，220mm*120mm方型資料。
3：作業壓力：0.3—0.8Mpa
4：外型尺度：650*210*270
FDJ-120風動切割鋸長處
1：90°直切,45°斜切,立式切開一體機。
2：運轉速度只要砂輪機的1/60,安全無火花。
3：切縫窄0.5mm,切開外表平整，精度高，無掛渣，無脫碳。
4：鋸條使用壽命長，單位切開成本低，一根鋸條使用壽命等同于50-80片砂輪切開片，較電能鋸節能60%
FDJ-120風動切割鋸使用方法：
1、了解所需切開的資料，如有必要能夠經過下降空氣壓力來下降鋸片的滾動速度。礦用錨桿錨索切割鋸寧夏 優質
2、保證結實固定了所需切開的資料，避免其移動。
3、氣動空氣馬達時，用手指按壓閥桿，然后開端切開。
4、用鋸的分量來操控切開壓力。關于較軟的資料來說，這么的分量已經滿足。過多的壓力會下降鋸片的速度。關于較硬的資料，能夠經過加壓的方法來下降鋸片的滾動速度。切開是堅持鋸垂直。鋸片的任何歪曲或傾斜都也許下降其使用壽命。（留意：避開切開后也許墜落的碎片。切開行將完結時，切勿使鋸碰到您的身體、工件或鄰近的其它人員。）
5、封閉空氣馬達時，開釋閥桿。
6、下次切開開端前，鋸片有必要堅持運動狀況。氣動鋸時，鋸片不能觸摸任何外表。
7、斷開空氣軟管時，封閉空氣軟管閥。斷開前，先翻開空氣閥給軟管減壓。
8、替換鋸片前，有必要斷開空氣軟管，并推進閥桿以開釋掉馬達內的壓力。
9、順時針滾動調整手柄以便開釋鋸片導桿上的張力。然后開釋側面板的鎖以便翻開側面板。然后從驅動輪上取下鋸片并將其從鋸帶導桿上松開。
FDJ-120 pneumatic hand cut saw is my company on risk, safety factor request especially high operating environment, such as chemical refinery. Natural gas mining. High wet tunnels, underwater and narrow space operations, especially in high gas coal mine explosion. The new multi purpose pneumatic Shanxi million Zejin of mining machinery and equipment limited company of independent research and hand cut things. It uses the imported pneumatic motor of Taiwan as power output, uses compressed air as power source, and does not have to power. The pneumatic handheld cut saw is not light, the operation is simple, it is convenient to carry zero spark, and improve the efficiency of operation. This product is safe and reliable is a high-risk career aspirations pneumatic incision.
FDJ-120 pneumatic cutting saw technical parameters:
1: applicable materials: stainless steel, aluminum, copper, chromium alloy, nickel base alloy, glass, fiber, wood, plastic, wire rope and so on.
2: incision size: 120mm*120mm circular data, 220mm*120mm square data.
3: job pressure: 0.3 - 0.8Mpa
4: the external scale: 650*210*270
FDJ-120 wind cutting saw length
45 degrees 1:90 degrees straight, oblique, vertical incision machine.
2: the speed of operation is as long as the 1/60 of the sand turbine, safe and free of spark.
3: the slit is narrow 0.5mm, the incision is smooth, the precision is high, no slag, no decarburization.
4: the long service life of the saw blade, and a unit cost is low and the service life of the saw blade and the equivalent of 50-80 wheel cut open, a power saw 60% energy saving
FDJ-120 pneumatic cutting saw use method:
1. Understand the material that needs to be cut, such as the reduction of air pressure to reduce the rolling speed of the saw blade. Cutting and sawing Ningxia high quality with mining bolt and anchor cable
2, ensure the sturdy fixation of the required open data to avoid its movement.
3. When pneumatic air motor, press the stem with the finger, and begin to cut.
4, use the component of the saw to control the cut pressure. For the softer data, this component has been satisfied. Too much pressure will reduce the speed of the saw blade. With more hard data, the rolling speed of the saw blade can be reduced by a pressurized method. The incision is to stick to the saw vertical. Any distortion or tilt of the saw may decrease its service life. (notice: avoid fragments that may fall after a cut. Do not make the saw touch your body, the workpiece, or the other people in the neighborhood when the cut will be finished.
5. When the air motor is closed, the stem is released.
6. Before the next opening, it is necessary to adhere to the movement of the saw blade. When a pneumatic saw, a saw can't touch any appearance.
7. When the air hose is disconnected, the air hose valve is closed. Before disconnecting, open the air valve and decompress the hose.
8. Before replacing the saw, it is necessary to disconnect the air hose and push the stem to release the pressure of Madane.
9, adjust the handle clockwise to release the tension on the sawing guide rod. Then release the lock of the side panel so as to open the side panel. Then remove the blade from the drive wheel and release it from the sawing guide rod.
