詳細介紹
騰達試驗儀器廠:
一、產品簡介:
隔墻板吊掛力試驗裝置依據JG/T169-2016《建筑隔墻用輕質條板》設計制造。拆裝方便,運輸途中占用空間小,造型美觀簡潔,清潔清掃保養也相對容易,其結構穩固耐用。試驗方法簡單,易操作
the product introduction:
The partition wall hanging force test device is designed and manufactured according to JG/T169-2016"Lightweight strip for building partition wall".It is convenient to disassemble and disassemble,occupying small space during transportation,beautiful and simple in design,relatively easy to clean and maintain,and its structure is stable and durable.Simple test method and easy operation
二、參數配置:
?荷載砝碼500N
?鋼板吊掛件1套
?外形尺寸:1900×1500×2600mm
?重量:220kg
econd,the parameter configuration:
?Load weight 500N
?1 set of steel plate hangers
?Dimensions:1900×1500×2600mm
?Weight:220kg
三、試驗過程:
?試驗條板的長度尺寸不應小于2m。
?取條板三塊為一組樣本,按圖1所示組裝并固定,上下鋼管中心間距為板長減去100mm,即(L-100)mm。
?板縫用與板材材質相符的專用砂漿粘結,板與板之間擠緊,接縫處用玻璃纖維布搭接,并用砂漿壓實、刮平。
Third,the test process
?The length of the test strip should not be less than 2m.
?Take three strips as a set of samples,assemble and fix as shown in Figure 1.The center-to-center spacing of the upper and lower steel tubes is 100mm,which is(L-100)mm.
?The seam of the board is bonded with special mortar which is consistent with the material of the board.The board is tightly squeezed between the board and the joint is covered with glass fiber cloth,and compacted and smoothed with mortar.
?24h后將裝有30Kg重,粒徑2mm以下細砂的標準砂袋用直徑10mm左右的繩子固定在其中心距板面100mm的鋼環上,使砂袋垂懸狀態時的重心位于L/2高度處(如圖2所示)。
?以繩長為半徑沿圓弧將砂袋在與板面垂直的平面內拉開,使重心提高500mm(標尺測量)。
?然后自由擺動下落,沖擊設定位置,反復5次。
?目測板兩面有無貫通裂縫,記錄試驗結果。
?試驗結果僅適用于所測條板長度尺寸以內的條板。
?After 24h,a standard sand bag with a weight of 30Kg and a fine sand of 2mm or less is fixed with a rope with a diameter of about 10mm on a steel ring with a center of 100mm from the plate surface,so that the center of gravity of the sand bag is in the hanging state.2 height(as shown in Figure 2).
?Pull the sand bag along the arc perpendicular to the plane perpendicular to the board surface with the radius of the rope as the radius to increase the center of gravity by 500mm(measurement of the scale).
?Then swing freely to fall,impact the set position,repeat 5 times.
?There are no through cracks on both sides of the visual plate,and the test results are recorded.
?The test results are only applicable to the strips within the length of the strip being tested.