Flush Ceramic Diaphragm Pressure Transmitter 沖洗陶瓷膜片壓力變送器 Advantages
Rugged, flush mounted ceramic
measuring cell
Extremely corrosion resistant
Measuring ranges from 1 to 50kgf/cm2
Shock and vibration resistant
Compact design
Zero and span adjustments
Applications
The transmitters are specially designed for
pressure measurement in sticky, high
viscous liquids.
Process control for food and beverage
industry
Tank level measurement
Chemical and petrochemical industry
Equipment and machinery for paint,
ink, resin and dough process
Cosmetic and pulp industry
Pharmaceuticals P510 series flush mounted pressure transmitters are
perfectly suitable for measuring static pressure in sticky
ａnd high viscous liquids in industrial applications. They
incorporate a fully temperature compensated
piezoresistive ceramic sensor which is corrosion
resistant, and a strong, durable flush mounted
diaphragm. The transmitters are available as absolute
ａnd relative pressure types with either 2-wire current or
3-wire voltage output. The versatile process connections
including thread, flange and clamp mounting are
available by customer requirement. The pressure to be
measured acts without transmitting liquid on a stable,
corrosion resistant ceramic measuring cell. Piezoresistive
resistors are attached to the cell and connected into a
Wheatstone bridge configuration. The output signal of
this bridge is converted into a standardized current or
voltage output signal. Technology Piezoresistive ceramic pressure sensor (Dry cell)
Pressure ranges 0~1 to 0~50kgf/cm2 absolute or gauge pressure
Pressure reference Gauge, absolute, vacuum and compound
Overload 1.5 × full scale without damage
Current output Voltage output
Electrical connection type 2-wire technique 3 or 4-wire technique
Full scale output signal 20mA ±0.5% 5V ±0.5%
Zero measured output 4mA ±0.05% 1V ±0.05%
Other signals available on request
Excitation voltage 12~36V DC
Load resistance max@24V 500Ω at 24V
Influence of excitation 0.01% FSO/V
Power ripple ≤500mV P-P
Reverse polarity Protected
Shock resistance ≤20g
Response time 1.5ms
Adjustment ±10% FSO/zero and span
Accuracy ≤±0.5% FSO
Linearity, Hysteresis & Repeatability ±0.2…0.4% FSO typical
Stability ±0.3% FSO/a @25°C
Cutoff frequency(-3 d B) ≤2kHz
Reference temperature 25°C
Operating temperature range -40~125°C
Compensated temperature range 0~70°C
Thermal sensitivity shift ≤±0.015%/°C typical
Thermal zero shift ≤±0.02% FSO/°C typical
Process connection PF3/4″male thread as a standard
Flange, Clamp mounted available
Other connections available on request
Process media Gases and liquids compatible with ceramic Al2 O3, 96%
Materials wetted by process Diaphragm : Ceramic Al2 O3, 96%
Housing : Stainless steel 316
Gasket O-ring : Teflon, Viton (HNBR, CSM, etc.)
Enclosure rating IP65
Explosion protection Ex d IIC T6 ( P519 )
Influence of mounting position Not critical
Weight Approx.(350g)
Options Clamp mounting for sanitary application
Sealed diaphragm with thread connection
Sealed diaphragm with flange mounting
Sealed diaphragm with capillary
Note : ① Cable version : 1.5m standard length, 4-wire, shielded with integral vent tube
② Vented gauge units must breathe dry, non - corrosive gases.
③ Connector version is vented through the removed pin, cable versions are vented through a vent tube inside
the cable sleeve
Input
Output
Electrical Specifications
Performance Specifications
Physical Specifications |
