雕刻機的日常保養維護

2023年07月18日 07:27:57人氣：1004來源：山東墨源數控設備有限公司

1.開機前首先檢查各部件是否在正常位置，各運動部件是否完好，導軌有油潤滑，然后開機底速動轉1~2分鐘，觀察是否有異常情況，等機床運轉正常后方能進行工作；

1. Before starting the machine, first check whether all parts are in the normal position, whether all moving parts are in good condition, and the guide rail is lubricated with oil. Then start the machine at the bottom and rotate it for 1 ~ 2 minutes to observe whether there are abnormal conditions. The machine can work only after the machine runs normally;

2.工情況選擇刀具、轉速、進刀量、加工速度及順，逆銑方向；

2. Select the tool, rotating speed, feed rate, processing speed and forward and reverse milling direction according to the working conditions;

3.整個加工過程不能用手或碎布等雜物接觸正在轉動的刀具，在清理石粉時要確保刀具停止運轉才能清除；

3. During the whole processing process, do not touch the rotating tool with hands or rags. When cleaning stone powder, ensure that the tool stops completely before removal;

4.作業完畢，關閉電源，清除各部位石粉，雜物。其他相關輔助工具必須放還原處；

4. After the operation, turn off the power supply and remove the stone powder and sundries at all parts. Other relevant auxiliary tools must be placed at the restoration place;

5.定期（依使用情況）清理電器箱內灰塵，檢查接線端子螺絲是否松動，以保證機器電路安全，可靠使用；

5. Clean the dust in the electrical box regularly (according to the use situation) and check whether the screw of the wiring terminal is loose, so as to ensure the safe and reliable use of the machine circuit;

6.工作臺面及導軌每天擦拭干凈，不可有石粉、油污雜質等；

6. The worktable and guide rail shall be wiped clean every day without stone powder, oil stain and impurities;

7.連續運行要保證冷卻水的潔凈及冷卻機的正常工作，不可以使水冷主軸電機出現缺水現象，定時更換冷卻水，以防止水溫過高；

7. For continuous operation, ensure the cleanness of cooling water and the normal operation of the cooler. Do not make the water-cooled spindle motor lack water. Replace the cooling water regularly to prevent the water temperature from being too high;

8.定期依使用情況）檢查機器各部件螺釘是否松動，以保證機器可靠；

8. Regularly check whether the screws of all parts of the machine are loose (according to the use conditions) to ensure the reliability of the machine;

9.每次機器使用完畢，要注意清理，務必將平臺及傳動系統上的粉塵清理干凈，定期（每周）對傳動系統（X,Y,Z,A,C等軸）潤滑加油；

9. Pay attention to cleaning every time the machine is used. Be sure to clean the dust on the platform and transmission system, and lubricate and refuel the transmission system (x, y, Z, a, C and other shafts) regularly (weekly);

10.機器若長時間不使用，應定期（每周）加油空走，以保證傳動系統的靈活性；

10. If the machine is not used for a long time, it shall be refueled and idled regularly (weekly) to ensure the flexibility of the transmission system;

11.主軸、工作臺和導軌面嚴禁敲打和沖擊，工作臺及道軌面不得亂放工具和毛坯及不相關的工件或物品；

11. It is forbidden to knock and impact the spindle, workbench and guide rail surface, and tools, blanks and irrelevant workpieces or articles shall not be placed on the workbench and track surface;

關鍵詞：接線端子

上一篇：濟南木工雕刻機日常怎么進行維護保養

下一篇：冷熱沖擊試驗箱蒸發器為什么會出現結冰

全年征稿/資訊合作 聯系郵箱：1271141964@qq.com

免責聲明

凡本網注明"來源：智能制造網"的所有作品，版權均屬于智能制造網，轉載請必須注明智能制造網，http://www.xashilian.com。違反者本網將追究相關法律責任。
企業發布的公司新聞、技術文章、資料下載等內容，如涉及侵權、違規遭投訴的，一律由發布企業自行承擔責任，本網有權刪除內容并追溯責任。
本網轉載并注明自其它來源的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或證實其內容的真實性，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請在作品發表之日起一周內與本網聯系，否則視為放棄相關權利。

大地资源网视频在线观看新浪,日本春药精油按摩系列,成人av骚妻潮喷,国产xxxx搡xxxxx搡麻豆

雕刻機的日常保養維護

免責聲明