In the engraving machine industry, there is a saying that seven points are used and three points are raised. Of course, few laymen know the truth. It is the so-called laymen watch the doorway and laymen watch the excitement. In fact, woodworking engraving machines, like cars, are maintained more than repaired, so that engraving machines can be used for a long time, Many users who have just come into contact with the engraving machine will have problems with the engraving machine due to illegal operation, which greatly shortens the service life of the engraving machine.

木工雕刻機如果做好維護保養工作，就可以很好地保證櫥柜門雕刻機的穩定運行，加工速度和加工精度，都可以得到很好的保障;木工雕刻機布維護和保養做得好，那么前期可能修幾次就修好，但是后期問題會越來越多，修好了這里那里就出問題，這是因為木工門雕刻機的一個或者幾個部件損耗比較嚴重，就會影響到其他部件的正常工作，越是不保養，被迫損耗的部件就會越多，整臺機器的運行就越容易出問題。那么櫥柜門雕刻機該如何保養維護?

If the woodworking engraving machine is well maintained, it can well ensure the stable operation of the cabinet door engraving machine, and the processing speed and accuracy can be well guaranteed; If the woodworking engraving machine cloth is well maintained, it may be repaired several times in the early stage, but there will be more and more problems in the later stage. If it is repaired, there will be problems here and there. This is because one or several parts of the woodworking door engraving machine are seriously worn out, which will affect the normal work of other parts. The more maintenance is not carried out, the more parts will be forced to be worn out, The more likely the whole machine is to go wrong. So how to maintain the cabinet door engraving machine?

一、工作環境

1、 Working environment

1、保證操作間環境溫度，特別注意冬季操作間溫度。木工櫥柜門雕刻機達到室溫，至少工作人員不會覺得很冷。

1. Ensure the ambient temperature of the operation room, with special attention to the temperature of the operation room in winter. When the woodworking cabinet door engraving machine reaches room temperature, at least the staff will not feel very cold.

2、查看所加油標準適用溫度，至少達到適宜溫度。

2. Check the applicable temperature of the refueling standard and at least reach the appropriate temperature.

3、機器不用時，若室溫較低倒出水箱里的水，防止凍裂水箱與水管。溫度對于櫥柜門雕刻機的影響不是很大，但由于很多客戶給絲杠加黃油，冬季也忘了清理，導致每次開機運行不開，有的工作室氣溫很低，雖然加了機油，可還是凍上了，機器運行不起來。

3. When the machine is not in use, if the room temperature is low, pour out the water in the water tank to prevent freezing crack of the water tank and water pipe. The temperature does not have a great impact on the cabinet door engraving machine, but because many customers add butter to the lead screw and forget to clean it in winter, they can't start up and run every time. The temperature in some studios is very low. Although the oil is added, it is still frozen and the machine can't run.

4.操作間的濕度不能太大，否則機器的電器配件很容易損耗

4. The humidity in the operation room should not be too high, otherwise the electrical accessories of the machine are easy to be worn out

5.操作間的電磁干擾一定要注意，干擾太大的話很容易使的櫥柜門雕刻機的加工精度受影響

5. Pay attention to the electromagnetic interference in the operation room. If the interference is too large, it is easy to affect the machining accuracy of the cabinet door engraving machine

二、定時清潔

2、 Regular cleaning

木工雕刻機使用完畢之后，一定要注意清理臺面和裸露在外的電器配件上的粉塵、木屑等，包括機器的導軌和滑塊，包括機器的絲杠和主軸電機。包括機器的工控箱，特別是工控箱里粉塵稍多就會導致電路板的運行處問題，很容易出現斷點，亂跑等情況。

After the woodworking engraving machine is used, be sure to clean the dust and sawdust on the table and exposed electrical accessories, including the guide rail and sliding block of the machine, including the lead screw and spindle motor of the machine. Including the industrial control box of the machine, especially a little more dust in the industrial control box will lead to problems in the operation of the circuit board, which is prone to breakpoints, random running and so on.

三、定期檢查

3、 Regular inspection

大部分木工雕刻機都是使用電腦來操作，而電腦一旦出問題的話整臺木工雕刻機就沒辦法用了，所以維護好電腦也是很重要。電腦維護注意一下以下幾個方面。

Most woodworking engraving machines are operated by computers, and once the computer goes wrong, the whole woodworking engraving machine can't be used, so it's also very important to maintain the computer. Pay attention to the following aspects in computer maintenance.

1、定期清理機箱灰塵，用空氣噴槍與小毛刷定期清理、小心灰塵過多引起工控卡出。注意機箱的散熱裝置，特別是夏天，小心控制線溫度過高燒壞電路板等設備。

1. Clean the dust of the chassis regularly, and clean it regularly with air spray gun and small brush. Be careful that too much dust will cause the industrial control card to come out. Pay attention to the heat dissipation device of the chassis, especially in summer. Be careful to control that the wire temperature is too high and burn the circuit board and other equipment.

2、定期清理電腦垃圾、整理磁盤碎片，優化電腦系統，保持電腦系統的穩定性。

2. Regularly clean up computer garbage, sort out disk fragments, optimize the computer system and maintain the stability of the computer system.

3、定期查殺電腦，但注意工作時不可以打開防毒程度，小心干擾

3. Check and kill the computer regularly, but pay attention not to open the anti-virus level during work and be careful of interference